/dev/video0 camera

README.md

@@ -26,10 +26,10 @@ These files provide a bash script for quickly deploying multiple octoprint insta
   * To add more printers at a later date, just run the script again!
 * General Linux (Ubuntu/Mint/RPiOS/Debian/Fedora/Arch/etc.)
   * __You do not need to install OctoPrint using any Wiki instructions, snap, etc. The script will do it for you.__
-  * octoprint_deploy uses systemd services, so avoid distros that do not use systemd by default (MX Linux)
+  * octoprint_deploy uses systemd services, so avoid distros that do not use systemd by default (MX Linux or chroot based systems like Chrome+crouton)
   * Basic guide video here: https://youtu.be/1YINWQ5fNn0
   * All commands assume you are operating out of your home directory.
-  * Install Ubuntu 18-22.X, Mint 20.3+, Debian, DietPi, RPiOS, Armbian, Fedora35+, or ArchLinux on your system (make sure your user is admin for sudo).
+  * Install Ubuntu 20+, Mint 20.3+, Debian, DietPi, RPiOS, Armbian, Fedora35+, or ArchLinux on your system (make sure your user is admin for sudo).
   * Install git if it isn't already: `sudo apt install git` or `sudo dnf install git` or `sudo pacman -S git`.
   * run the command `git clone https://github.com/paukstelis/octoprint_deploy.git`.
   * run the command `sudo octoprint_deploy/octoprint_deploy.sh`.

octoprint_deploy.sh

@@ -364,7 +364,7 @@ write_camera() {
 }
 
 add_camera() {
-    
+    PI=$1
     if [ $SUDO_USER ]; then user=$SUDO_USER; fi
     echo 'Adding camera' | log
     if [ -z "$INSTANCE" ]; then
@@ -386,19 +386,9 @@ add_camera() {
         done
     fi
     
-    dmesg -C
+    if [ -z "$PI" ]; then
-    echo "Plug your camera in via USB now (detection time-out in 1 min)"
+        detect_camera
-    counter=0
+        
-    while [[ -z "$CAM" ]] && [[ $counter -lt 60 ]]; do
-        CAM=$(dmesg | sed -n -e 's/^.*SerialNumber: //p')
-        TEMPUSBCAM=$(dmesg | sed -n -e 's|^.*input:.*/\(.*\)/input/input.*|\1|p')
-        counter=$(( $counter + 1 ))
-        if [[ -n "$TEMPUSBCAM" ]] && [[ -z "$CAM" ]]; then
-            break
-        fi
-        sleep 1
-    done
-    dmesg -C
         #Failed state. Nothing detected
         if [ -z "$CAM" ] && [ -z "$TEMPUSBCAM" ] ; then
             echo
@@ -416,6 +406,13 @@ add_camera() {
             echo -e "Camera detected with serial number: \033[0;34m $CAM \033[0m" | log
             check_sn "$CAM"
         fi
+        
+    else
+        echo "Setting up a Pi camera service for /dev/video0"
+        echo "Please note that doing this with USB cameras may lead to issues."
+        echo "Don't expect extensive support for trying to fix these issues."
+    fi
+
     echo "Camera Port (ENTER will increment last value in /etc/camera_ports):"
     read CAMPORT
     if [ -z "$CAMPORT" ]; then
@@ -454,6 +451,10 @@ add_camera() {
     #Need to check if this is a one-off install
     if [ -n "$camopt" ]; then
         write_camera
+        #Pi Cam setup, replace cam_INSTANCE with /dev/video0
+        if [ -n "$PI" ]; then
+            sed -i "s/cam_$INSTANCE/video0/" /etc/systemd/system/cam_$INSTANCE.service
+        fi
         systemctl start cam_$INSTANCE.service
         systemctl enable cam_$INSTANCE.service
         udevadm control --reload-rules
@@ -480,6 +481,22 @@ detect_printer() {
     dmesg -C
 }
 
+detect_camera() {
+    dmesg -C
+    echo "Plug your camera in via USB now (detection time-out in 1 min)"
+    counter=0
+    while [[ -z "$CAM" ]] && [[ $counter -lt 60 ]]; do
+        CAM=$(dmesg | sed -n -e 's/^.*SerialNumber: //p')
+        TEMPUSBCAM=$(dmesg | sed -n -e 's|^.*input:.*/\(.*\)/input/input.*|\1|p')
+        counter=$(( $counter + 1 ))
+        if [[ -n "$TEMPUSBCAM" ]] && [[ -z "$CAM" ]]; then
+            break
+        fi
+        sleep 1
+    done
+    dmesg -C
+}
+
 remove_instance() {
     echo
     echo
@@ -1371,4 +1388,8 @@ fi
 if [ "$1" == replace ]; then
     replace_id
 fi
+
+if [ "$1" == picam ]; then
+    add_camera true
+fi
 main_menu